真空钨丝烧结炉温度可达2200℃，真空钨丝烧结炉为立式真空电炉，由炉盖、炉体、炉底和真空机组组成，炉壳内层是不锈钢，外层是碳钢，两层之间用循环水冷却。炉壳上设有抽气口、观察孔、热电偶孔、保护气氛进出口、防爆口等。真空钨丝烧结炉加热元件采用钨丝加热，加热元件的周围有多层钨片、钼片和不锈钢组成的隔热屏装置。炉底是由内外板焊接而成，中间水冷。可上下升降方便装卸料。

The electric furnace is a vertical vacuum electric furnace, which is composed of furnace cover, furnace body, furnace bottom and vacuum unit. The inner layer of furnace shell is stainless steel and the outer layer is carbon steel. The two layers are cooled by circulating water. The furnace shell is provided with air extraction port, observation hole, thermocouple hole, protective atmosphere inlet and outlet, explosion-proof port, etc. The heating element adopts tungsten wire for heating, and the heat shield device composed of multi-layer tungsten sheet, molybdenum sheet and stainless steel is arranged around the heating body. The bottom of the furnace is welded by inner and outer plates, with water cooling in the middle. It can be lifted up and down to facilitate loading and unloading.

真空钨丝烧结炉广泛应用于无机材料（如陶瓷密封件、氧化锆、氧化锌、二氧化铝等）、及金属材料（如硬质合金）在真空或保护气氛中烧结制备，也可用于对烧结环境有洁净要求的材料进行热处理。同时适用于大专院校、科研单位进行中试批量生产使用。

Vacuum tungsten wire sintering furnace is widely used for sintering inorganic materials (such as ceramic seals, zirconia, zinc oxide, alumina, etc.) and metal materials (such as cemented carbide) in vacuum or protective atmosphere. It can also be used for heat treatment of materials with clean sintering environment. At the same time, it is suitable for colleges and universities, scientific research institutions for pilot proction.

结构特点Structural features:

1、炉内设有充气超压防爆系统；

The furnace is equipped with an inflatable overpressure explosion-proof system;

2、真空钨丝烧结炉炉压防爆装置，防止炉内过压；

Vacuum tungsten wire sintering furnace pressure explosion-proof device to prevent furnace overpressure;

3、全不锈钢设计，水路洁净不生锈，不结水垢，防止水路堵塞；

 All stainless steel design, clean waterway, no rust, no scale, to prevent waterway blockage;

4、程序升温，预设工艺升温，一键操作，并配红外测温；

 Temperature programmed, preset process temperature rise, one key operation, and equipped with infrared temperature measurement;

5、可升级PLC+触摸屏控制方式自动化程度高；

 It can be upgraded PLC + touch screen control mode with high degree of automation;

6、电路设有断水、过流、炉超温及水超温报警及保护功能；

The circuit is equipped with water cut-off, over-current, furnace over temperature and water over temperature alarm and protection functions;

7、炉体设有温度监测装置，实时监测炉体温度，方式过烧损坏炉体。

The furnace body is equipped with a temperature monitoring device to monitor the temperature of the furnace body in real time.

安装要求Installation requirements:

1、海拔高度不超过1000m；

The altitude shall not exceed 1000m;

2、环境温度在5～40℃范围内；

The ambient temperature is in the range of 5 ~ 40 ℃;

3、使用地区设计湿月每日设计相对温度的月平均值大于90％，同时该月每日设计低温度的月平均值不高于25℃；

The monthly average value of daily maximum relative temperature in the wettest month in the use area is more than 90%, and the monthly average value of daily minimum temperature in that month is not higher than 25 ℃;

4、周围没有导电尘埃，爆炸性气体及能严重损坏金属和绝缘的腐蚀性气体；

 There is no conctive st, explosive gas and corrosive gas that can seriously damage metal and insulation;

5、电源：设备输入电压380V，三相五线制、电流60A以上、电缆截面25平方毫米以上；

Power supply: the input voltage of the equipment is 380V, three-phase five wire system, the current is more than 60A, and the cable cross-section is more than 25mm2;

电源箱内应具备380V和220V电源；

The power box shall be equipped with 380V and 220V power supply;

6、水源：需具备冷却水设备（如冷水机、冷却塔），水管连接到真空炉安装处。

 Water source: cooling water equipment (such as chiller and cooling tower) shall be provided, and the water pipe shall be connected to the installation place of vacuum furnace.

真空钨丝烧结炉厂家哪个好？

洛阳西格马高温电炉可生产真空钨丝烧结炉、真空钨丝加热炉、真空烧结炉。